====================================
LAPIDARY ARTS and FACETERS DIGEST
====================================
Issue No.38 - Tuesday January 7, 2003
====================================
Moderated by: Thurmond Moore III
====================================
Committed to carrying on the fine works started
by Hale Sweeny and Jerry Dewbre
====================================
Click a link below to post to the list:
for faceting questions  faceters@caprock-spur.com
for lapidary questions lapidary@caprock-spur.com
====================================
From the Moderator: Up until a couple of hours ago
there were no post. Thanks to Douglas Turet's post
the digest was saved from non publication  today.

Thurmond
====================================
Index to Today's Digest

01  Re: Gemstone Irradiation

====================================
Message:01

Subject: Re: Geiger Counter
Date: Tue, 07 Jan 2003 12:07:09 -0500
To: faceters@caprock-spur.com
From: "Douglas Turet" <anotherbrightidea@hotmail.com>


Hi again, Gerry,

     Since it sounds like you're still quite concerned about the gem  
irradiation issue, perhaps I can help, in some small way. Since the middle
of 1988, when I'd picked up my own Geiger Counter (the same one, it turns
out, that Jon Rolfe had recommended; the hand-held unit with the
partially-exposed tube), I've measured every parcel of rough I've bought,
small or large, but have only once yielded a sound. (And even then, it was
only on a parcel of metamict Zircon from the Hart's Range area of Australia,
where I'd have been shocked _not_ to have heard a click or three.)
     If you're buying by the kilo, as you've said, and you'd sleep better
knowing one way or t'other, I think I may be able to lend a hand... I'm
always in the market for nice pieces of hard-to-get facetables, especially
blue or color-change Sapphires, fine Rubies, Emeralds or Tanzanites, larger
than 5cts., in the rough. If you have any on hand that are of good color and
clarity, would you like to swap for my Geiger counter? It's still in its
original box/bubble wrap, and still has its original owner's manual
(actually, more like a pamphlet, as I recall). Frankly, I'm not using it, at
this point, so if you can...

All the best,
Doug

Douglas Turet, GJ
Lapidary Artist, Designer & Goldsmith.
Turet Design
P. O. Box 162
Arlington, MA 02476, U.S.A.
Tel. (617) 325-5328
Fax: (928) 222-0815
Email: anotherbrightidea@hotmail.com


====================================

RESOURCES FOR LAPIDARIES ~

Hale Sweeny's Lapidary Digest Archives http://www.lapidarydigest.com/
International Lapidary Association http://www.gemcutters.org
http://webdev.archive.org/ then enter www.liccini.com

RESOURCES FOR FACETER'S ~

Facetron: http://www.facetron.com/
Graves: http://www.rockhounds.com/graves/
MDR: http://www.mdr-facet.com/
Polymetric: http://www.polymetricinc.com/
Ultra-tec: http://www.ultratec-facet.com
Fac-Ette Manufacturing Company: (910)256-9248
http://www.fac-ette.com/ 800-336-9248.
Raytech Industries: http://www.raytech-ind.com
Rock Peddler: 1-800-416-4348 / www.rockpeddler.com

====================================

RESOURCES FOR GEMOLOGISTS ~

Accredited Gemologists Association, http://aga.polygon.net/
American Gem Society, (AGS) 702-255-6500
American Gem Trade Association, (AGTA) http://www.agta.org
Gemmological Assc. & GTL / Great Britain, http://www.gagtl.ac.uk/gagtl
Gemmological Association of Australia, http://www.gem.org.au
Gemological Institute of America, (GIA) http://www.gia.edu.giagem
International Gem Society (IGS) web site is: http://www.gemsociety.org
International Colored Gemstone Association, http://www.gemstone.org
My Gemologist http://www.mygemologist.com

====================================

FACETING GUILDS (Alphabetically, World) ~

*Charleston Faceting Guild, South Carolina, wmcnay@mindspring.com.
*Columbia-Willamette Faceter's Guild, http://www.facetersguild.com/
*Danish Faceters Guild, http://medlem.spray.se/danfacet/
*East/Central Florida:Tomoka Gem and Mineral Society's Faceters Guild,
Don Cameron: ghgemcutter@earthlink.net
*Eastern Mass Faceter's Group, rockpeddler@attbi.com
*Faceter's Forum Society-LaPorte, IN VESteele@aol.com
*Faceter's Guild of N. California, Wayne Meissner, lklomp@cnetech.com
*Faceter's Guild of S. California, Jerry W. Carroll, (818)348-6327
*Intermountain Faceter's Guild, Carl M. Unruh, (360)385-3753
*Midwest Faceter's Guild, Tyler Miller,  tmiller277@comcast.net
*Mid-Williamette Faceters Guild, Albany, Oregon, Michael E. Bumcrot;
E-mail @ MBumcrot@valleyoilco.com
*Moreton Bay is a branch of the Australian Facetors' Guild, Brisbane,
Queensland. http://cwpp.slq.qld.gov.au/afg
*New Mexico Faceter's Guild, Nancy Attaway, attaway@highfiber.com
http://www.attawaygems.com/NMFG
*North Puget Sound Faceting Guild, Keith Wyman, tfw@fidalgo.net
*Tacoma Faceting Guild, Chuck Bloch chuck_b@prodigy.net
*Texas Faceter's Guild, Jill Rowlands, gemsbyj@aol.com
*Seattle Faceting Club (LeonardBahr@prodigy.net)
*United States Faceting Guild (Keith Wyman, tfw@fidalgo.net)
http://www.usfacetersguild.org/events.shtml
*Vancouver Island Faceters' Guild - British Columbia, Canada.
wrheitland@shaw.ca

(Add your faceting organization here, US or International - Write to
( owner-lapidary@caprock-spur.com or owner-faceters@caprock-spur.com )

====================================

TODAY'S FUNNY ~

Computers are female
The top six reasons computers must be female:

6. As soon as you have one, a better one is just around the corner.

5. No one but the creator understands the internal logic.

4. Even your smallest mistakes are immediately committed to memory for future reference.

3. The native language used to communicate with other computers is incomprehensible to everyone else.

2. The message "Bad Command or File Name" is about as informative as

"If you don't know why I'm mad at you, then I'm certainly not going to tell you".

AND THE NUMBER ONE REASON COMPUTERS ARE FEMALE:

As soon as you make a commitment to one, you find yourself spending half of your paycheck on accessories for it.

 
=====================================

REFLECTIONS AND TIDBITS:

" If we are strong, our strength will speak for itself.
If we are weak, words will be of no help."
--- John F. Kennedy
 
=====================================
BUSINESS SECTION:  No Messages
=====================================

CLASSIFIED ADVERTISEMENTS:


Rough to Cut
If you're looking for quality facet rough please check out Rough to Cut,
http://www.roughtocut.com. We offer a wide range of quality facet rough
from Aquamarine to Zircon. Large selections in stock currently of Beryl,
Garnets & Tourmalines. Please check us out & when you do, why not give a
try to our contest, you could win a 5ct + piece of Spessartite garnet
facet rough.

Noel
Rough to Cut
http:www.roughtocut.com

11142002P
********


Subject: AD
Date: Thu, 31 Oct 2002 20:50:44 -0800
To: faceters@caprock-spur.com
From: "P. Miklik" <b-daw@pacbell.net>

AVAILABLE FOR SALE
Contact b-daw@pacbell.net

ZIRCONS
Honey, red & brown zircons, 10g parcels @$20/parcel

GARNETS
Red Garnet $8/g, eye clean-slightly included
Spessartine Garnet $7.50/g, slight-moderately included
Malaya Garnet $6/g, good eye clean roughs
Tunduri Garnet $10/g, eye clean-slightly included

TOURMALINES
Pink Tourmaline $20/g, eye clean-slightly included
Red Tourmaline $10/g, slight-moderately included
Bicolor Tourmaline $15/g, eye clean
Watermelon Tourmaline $20/g eye clean
Green/Green Blue Tourmaline $10/g, eye clean roughs

SAPPHIRES 
Blue, Green & Blue/Green Sapphires $35/g, eye clean-slightly         
included, up to 1g.

BERYL  
Blue Beryl (Aquamarine) $6/g, eye clean-slightly included crystals
Green Beryl (Emerald) $10-$50/g, eye clean-slightly included crystals,
zoned green
Cabbing Grade Aquamarine $3/g

11012002P
********

Rock Peddler
Complete online discount catalog for cabbing and faceting machines, wheels,
laps, polishes, diamond saws, diamond blades, and general lapidary supplies
at http://www.rockpeddler.com.

09272002P
********

Gewelers Gems
e-mail: sales@jewelersgems.com
Solid copper laps 1/4 thick 8" and 6"  you can charge both sides with
diamond. http://www.jewelersgems.com/faceting_laps.htm

03222002P
********

NOW ONLINE!  RRGaetan Gem Rough - Featuring excellent, facet-grade,
Colombian Emerald rough! PLUS, Chrome Tourmaline, Achroite Tourmaline,
Golden Chrome Tourmaline, Aquamarine, Spess, Mint and Malaya Garnets,
and more! For photos and more information, visit us at rrgaetan.com.

11242002RP
********

===================================

COMPETITIONS:

For All National and International Masters, Past-Masters and
World-Class Cutters:

This post is simply a reminder that in 2003 the USFG will host its
first National and International Faceting Competition.  It is called
the North American Faceting  Challenge -- 'NAFC.'   Since the designs
and rules were first published in the 2001 September Issue of  the
USFG's Newsletter, and since they have not been published since 2001,
some of you, who are most capable - skill-wise, may not
know about the competition, and some of you may have forgotten.   The
"NAFC" is an OPEN Competition.   Please note:  The designs and rules
can be downloaded at  <http://www.usfacetersguild.org/events.shtml>.
The closing date is June 20th, 2003;  the amount of time between the
present date and June 20th, 2003 should be enough for all Master
cutters to cut the two required designs -- Fred Van Sant's "Four
Star," and Charles Covill's "Wind Wheel No. 2."   If   further
information is needed, please contact me at <clmoon@pacbell.net>.

Charlie Moon

*****

Subject: First USFG faceting list design competition.
Date: Thu, 21 Nov 2002 16:29:21 -0800
To: faceters@caprock-spur.com
From: Dan Clayton <dclayton@speakeasy.org>

First USFG faceting list design competition.

Design: Hexagon or Hexagon Cushion in  Colorless or Colored Topaz

Judging: Highest number for total ISO values at 0, 10, 20,30, 40
and 50 degree tilt with five degree head shadow in GemFramx will
win. Example parameters are given below to achieve this configuration.
Online designs must be submitted by January 10, 2003. Design and
cut entries should have the design posted by that date but stone judging
will take place at the OPLC Hobnob in Tucson in February 2003.

Publication: All entries will be posted on the USFG faceting list site
and possibly on the USFG site as well. Designs may be included in
a USFG list CD. Designers maintain copyright to their designs but
must allow posting on the USFG faceting list site. Posting or publishing
elsewhere is not only permitted but encouraged.

Followup: Additional contests may be held for other shapes and
materials if there is sufficient interest and participation.

RI                                       1.61
head shadow                      5 degrees
ignore glare                     no (default)
tilt movie                       yes (default)
starting tilt direction    0
ending tilt direction     5 (default)
maximum tilt angle      50
tilt increment                   10
suppress VGA                     no (default)
concave                          no (default)
COS files                        no (default)
ISO files                                no ( you can enter yes if you wish
 but it will fill your disk )
DISP files                       no (default)
exit files                               no (default)
starting file #                  increment each run if you wish to save images

Values for ISO  will be summed and used as ISO total.
ISO Total will be deciding factor in judging but there will be 30
points deducted for a missed meetpoint. Fractional

Special recognition will be given to most original design as determined
by team of four judges selected by Jeff Ford or delegate/s.

Classes:

 Individual,
 all work must be done by one individual. In the
case of a fractional indices or an incomplete design a design
coach will explain how the problem can be fixed and the
entry will be moved to Coached class.

Team/Coached,
more than one individual from a club, guild or area may work together
 as a team. If an individual wishes coaching they may do so but most
work must be done by the entrant with only suggestions by coach. This
means Fred Van Sant or some other designer can not do a design that you
enter as your own. I encourage friends, club/guild members to enter as a
team. Do not hesitate to enter if you need some coaching. We have design
mentors who are happy to help you.

 Modified,
for a public domain design or a copyrighted design that the copyright holder
gives you permission to use. You enter design with modified angles, new tiers
or deleted tiers which gives "optimum" performance as determined by ISO
total. We will post at least two very basic designs you can enhance as you
please.

Design and Cut,
design will be posted and ISO Total noted but beauty of the finished stone
will be the judging criteria. Stones will be judged at the OPLC Hobnob in
Tucson. Individual, Team/Coached and Modified designs will be judged
separately.




I hope this format will encourage design and optimization  oldtimers and
newcomers to get involved and hopefully develop their skills. All
entries will be posted on the site and may drive some traffic and interest.
I think ISO Total is as good as any single value to evaluate design
performance but we will look to improve criteria in the future.


Dan Clayton


===================================

SHOWDATES:

~ CALIFORNIA


FACETERS SYMPOSIUM 2003
  Presented by the Faceter's Guild of Southern California
    At the Seaside GEMboree AFMS/CFMS Convention & Show
           Ventura, California June 6-7-8, 2003


     You are invited to participate in the Faceters
Symposium 2003 which will be held at the Seaside Park
(Ventura Fairgrounds) at Ventura, California during the
AFMS/CFMS Convention & Show.  The Faceters Symposium dates
are June 6th, 7th, & 8th.  That is Friday, Saturday, &
Sunday.  The CFMS GEMboree is on those dates as well as on
Thursday the 5th of June.  All of this is at the same
location, just a hundred yards from the beach.

     The Faceters Symposium will feature ten speakers, who
will have presentations covering various parts of gemstone
faceting interests.  A Hospitality Hour on Friday evening
and a Saturday Awards Luncheon are also part of the
Symposium.  There will be competitions at the Novice,
Advanced, & Masters levels.  Get started on your
competition entry soon.

     The CFMS GEMboree itself will have buildings that have
exhibits on display, dealers with their wares to offer,
demonstrators to show how it is done, and speakers with
presentations covering other lapidary fields of interest.

     For information & costs regarding the Faceters
Symposium (including competition information), your contact
is listed below.  Ask for one of the Packets.  Be sure to
state your snail mailing address so that a Packet can be
mailed to you.

Glenn Klein, Chairman
24001 Muirlands Blvd., Space #79
Lake Forest, CA 92630        email:   glennklein@yahoo.com



===================================


LAPIDARY ARTS and FACETERS DIGEST PERSONALS:


KANSAS: If anyone in the central portion of the country from Oklahoma city
to Wichita to Kansas City would be interested in forming something like the
Flatland Facet Guild or some such name give me a line at
faceter@bigfoot.com
Larry W. Davis
******

ILLINOIS - MISSOURI (Central Area, hubed around St. Louis, Missouri) A
group of 4 faceters have met and we had a great time. We intend to meet
again and would like to have fellow faceters join our group. I received an
email from another Newbie that expressed interest in attending our next get
together. Faceters from any and all areas are welcome... It's swell to meet
personally and exchange tips and hints! COME JOIN OUR GROUP! It's FREE! ;o)
Doug Smith, Alton, IL .at: gembin@spiff.net
******

INDIANA: I moved to Valparaiso, (Northwest) Indiana, about three years ago.
Are there any clubs in this area? or is there anyone interested in starting
one? I do faceting and some cabbing. Not much here but cornfields. Nice
scenery, but I get sooooooo lonely. LOL Let me know. (Bill) "William
J.Pysnack" <wjpin@home.com>
******

S.E. LOUISIANA: Anyone in or around the New Orleans, LA area wishing to
form a club or have get togethers for faceting, discussions, cabbing,
procurement, etc. Please contact me via email @ tbird@bayouself.org. (Thom
Bird - Chalmette, LA)
*****

MISSISSIPPI: If anyone is near Meridian Mississippi and would be interested
in forming some kind of club or just get together with faceting and/or
cabbing please e-mail me at jennings@netdoor.com Thanks, Jim
*****

TEXAS: Anyone in the Corpus Christi or Coastal Bend area that is interested
in starting a local faceter's guild contact me at: hankswan@earthlink.net or
gemscc@msn.com or telephone 361-857-2405 (days) or 361-992-1296
(evenings).Hank swan
******

WASHINGTON DC.(Rockville Md area) Looking for folks to get together
occasionally to facet. I have just started faceting and am also interested
in sphere making (infinate # of facets) Robert Winfield
winfielr@inra.nimh.nih.gov
******

=============================================
Lurking is fine, but participation is more fun!! Get involved!!
=============================================

LIST and WEBSITE INFO~

LAPIDARY ARTS and FACETERS DIGEST Staff
is produced by
Thurmond Moore III
owner-lapidary@caprock-spur.com

Tempie Francis, Attorney at Law / Legal Advisor

==============================================
==============================================

The LAPIDARY ARTS and FACETERS DIGEST is never sent unsolicited.
You are receiving it because you subscribed to it at our digest subscription page at:

http://dns2.caprock-spur.com:81/guest/RemoteListSummary/LapidaryArtsDigest

To unsubscribe, just use the link below and follow the instructions there:

http://dns2.caprock-spur.com:81/guest/RemoteListSummary/LapidaryArtsDigest

List Posting Guidelines and rules can be found at:
http://www.gemcutters.org/rules.htm
====================================
Web Site  http://www.gemcutters.org
Archives: http://www.gemcutters.org/archives.htm
====================================
Published Monday thru Friday, except holidays
from Spur,Texas
====================================
The Lapidary Arts Digest is moderated by:
Thurmond Moore III

==============================================
List Policy: http://www.gemcutters.org/rules.htm
==============================================
Share your love of lapidary with a friend!
==============================================